iDS X64 ALARM PANEL

Installing the Hype Module

Mount the hype module to the wall

HYYP Module will connect just above the X64 Label with the red cable to the top. Don;t pull on the cables, work with the plastic plug.

Power the Hype Module from the panel auxiliary (-) 12V Left terminal on Module Common Ground (+) right – client has existing gsm radio (may be using the same terminal that we need for the HYYP)

Connect the Network Cable to the HYYP Module and to the internet router.

Make sure each core of the cat 5 cable is pushed up to the end.

Make sure the jacket is pushed right in

Green link light indicates a network link and the orange light indicates network activity

Now go to instructions "how to reset comms port"

RESET COMMS PORT

First go into installer programming mode On the keypad do the following; [#][9999][*] this is the default installer code, use your installer code if you have set one

Enter 196*

The display will show 123456, but re-enter 123456*

Press # to update the panel

INSTALL THE HYYP APP

Make sure your smart phone is on the wi-fi network

Search for IDS HYYP smart home app on playstore

Install as you would any other Playstore APP

Open the HYYP app on the device, while connected to the local network or wifi

Sign Up the Customer

The password must have at least six characters

Add the site, Give the site a name,

--> Continue

Manually add the IMEI number or scan it

After scanning the code, the app is waiting for panel activity, go to the panel and repeat the “reset comms port procedure “123456”” describe above.

After updating it will be confirmed and you will be logged in.

The zone allocation is achieved by dipswitch combinations.

1 on- Zones 17 - 24

2 on - Zones 25-32

1&2 on - Zones 33-40

3 on- Zones 41-48

1&3 on - Zones 49-56

2&3 on - Zones 57-64

• Zones 9-16 are reserved for the onboard expander

The yellow LED on the expander displays no error when it is solid.

If the LED is pulsing on and off it indicates and error.

Pulese 1 and off - Low Battery

Pulsing twice - No activity on Serial Bus

Pulsing three times - no x series message detected.

Pulsing 4 Times - no message for the specific peripheral from the panel

Pulsing 5 times - Awaiting Tamper change

Pulse 6 - Expander Not registered on panel

Pulse 7 Expander Tamper violated.

The expanders are daisy chained one after another, and addressed by dispswitch.

The basic steps are:

Connect the expander to the bus in series, ie it must be daisy chained to the last connected device.

Allocate zones to the expnder by setting the dipswitches

Check the LED status light for errors

Each step is explained in more detail in the FAQ under that specific question.

The expander should start up and function

Mount the Module by screwing to the wall

Connect the module to the panel serial pins

Power the module from the panel Aux Output

Connect the Module to an Internet Router with Category 5/6 cable

Reset the comms on the Keypad to update the panel

Download and Install the IDS HYYP Smart Home App from the playstore while connected to the site wifi

Complete the Customers details and register

Give the site a name and continue

Scan the device EMEI number from the device box

Go back to the Keypad and reset comms as before

You should then be logged in to the device.

• each step is described in more detail in the FAQ under the specific question.

Remove all power from the panel

Press and hold the default button

Reconnect power with the button still depressed untill the status LED starts flashing

Release the button

Setting a stay profile on ids x64

Hold the 3 Key until a profile number appears on the Lcd screen

Then you press the star button, which brings up the zone number display. You will scroll through here to add zones to this stay profile. The panic button on the curve LCD keypad is used to scroll through the zones.

Scrolling through the zones, each zone will be labelled Y or N, indicating whether it is bypassed in this stay profile or not. To Change the status N to Y or Y to N you press the * Key, after setting a zone you can continue scrolling with the panic button.

After selecting the zones required you can press the # key to exit.

To use the stay arm function you will hold down the 5 key until the arm led lights and stay armed shows on the screen

To disarm you will enter your code.

To use the stay arm function you will hold down the 5 key until the arm led lights and stay armed shows on the screen

To disarm enter your code.

To setup partitions on the X64, you need to program the correct location. Location 201 = partition 1 Location 202 = partition 2 ……. Location 208 = partition 8

Again go into installer programming mode, on the keypad do the following; [#][9999][*] this is the default installer code, use your installer code if you have set one [201][*] Location 201 for partition 1

Again go into installer programming mode, on the keypad do the following; [#][9999][*] this is the default installer code, use your installer code if you have set one

[201][*] Location 201 for partition 1 On LCD keypad

[Zone Number][*] This is to choose the “Zone number” e.g. 10* for Zone 10

To enable the Zone for Partition set option to Y by press [*] Key

When finished press the [#] key

For example to enable Zones 9-12 on partition 1

[#][9999][*]

[201][*]

[9][*]

[*]

[10][*]

[*]

[11][*]

[*] [12]

[*]

[*]

[#]

First go into installer programming mode On the keypad do the following; [#][9999][*] this is the default installer code, use your installer code if you have set one

[1][*] this is location 1 which allows you to program any zone number

[Zone number][*] enter the zone number to program then press the [*] key

[Zone type][*] the zone values are the same as our IDS816/ IDS1632 panels

You can just continue programming Zones [Zone Number][*] [Zone type][*] [Zone Number][*] [Zone type][*] Etc….

To end programming Zone Types Press the [#]

Zones 9 - 64 are disabled by default and you will need to program a zone type,

for example to enable/set Zone type for Zones 9-16 – the Zones on the Plug-in expander do the following:

[#][9999][*] Installer code* [1][*] location

1* (Location 1 is a root location for zones)

[9][*][1][*] Zone 9* (or sub location 9 = Zone 9) then 1* = Entry/Exit zone

[10][*][2][*] Zone 10* (or sub location 10 = Zone 10) then 2* = Follower zone

[11][*][4][*] Zone 11* (or sub location 11 = Zone1 1) then 4* = Instant Zone

[12][*][4][*]

[13][*][4][*]

[14][*][4][*]

[15][*][4][*]

[16][*][4][*]

[#] Press the [#] key to Exit location 1

[#] Press the [#] key to exit programming mode

ADD USER CODE

1. Hold [*] till BEEP, then [MASTER CODE]

[*] [0] [*] [NEW USER CODE] [*], continue until all codes are entered then

[#] to exit

To add a sub user (user must install HYYP APP)

click on the Site that you wish to share,
click the three dots in the top right hand corner
tap “Users.”
Click the add user icon in the top right hand corner to add a new sub-user.
enter the sub-users HYYP ID or scan their QR code (You can find this by going to
their “My Profile” option on the new user’s cell phone)
You will then select the partitions that the sub-user is entitled to use as well as the permissions they are allowed to access per partition and when finished you will click the arrow in the top left hand corner to exit and your sub-user will then be added.

1. Make sure that the recorders time, date and time zone is correct, set the NTP server, you can use time.windows.com as the ntp server

2. Select the alarm option from the main menu on XVR, the enable MD for all required cameras, and set the post record setting to 30s.

3. select storage → Schedule, and set the schedule to MD, disable general , set pre-record to 30s

4. Select storage -> record and set the sub stream to auto

5. from main menu select camera –> encode.
Enable substream option
Set resolution to D1
Frame rate to 10
Bitrate to 192

6. From the main menu select network –> p2p
Enable the button
make sure the device is online

The DVR is now prepared for integration with HYYP

First prepare your recorder for the integration – see the relevant steps in this FAQ

1. open the HYYP app and select the site you want to link.
With the site selected click on the CCTV menu at the top of the page.

2. Click on the + (add device) square
Select the p2p tick
Fill in the details on the form – scan the DVR QR code, and fill in the desired channel number.

3. Select the site and click on the camera icon,
choose the camera and click on the link icon
Select the partition
then select the zone you wish to link to the camera by checking the relevant box
then click the link button

See How to View Cameras Live on HYYP APP

Select the relevant site
Click CCTV link at top of page
Click camera Icon and select camera view