Dace Dura Swing Motor



  • 1.Dace Dura Swing
    All about the Dace Dura-Swing Motor
  • How Do I Program The Limits On A Dace Dura-Swing Swing Gate
    Gensix Technical26-04-2021

    There are two limit switches and a limit rotor in each operator. The function of these is to stop the operators turning when the limit switch is struck by the rotor which is attached to the main shaft.Before setting up the limit switches you have to establish the closing direction of the operators. The operators should automatically drive to the closed position when first powered up but as each site is unique it may not. Apply power to the motor and take note of the direction that the shaft turns.

    NOTE: If it is determined that the operators are turning the correct way, continue to set up the limit switches as shown below.If the operators are turning the incorrect way you must reverse the motor wires. Follow the instruction below before continuing to set up the limit switches.

    reverse-dace-swing

    Remove the power. Reverse the motor wires at the limit diodes as shown above.
    The operators should be running in the correct direction i.e. when the CLOSE LED is on the gates must be closed and when the OPEN LED is on the gates must be open. Now proceed to set up the limit switches.

    setting dace duraswing limits procedure
    1. Stand the battery up in a vertical position to allow for access to the limit rotor

    Diagram for limit settings on dace duraswing
    Instructions for setting the limits on dace duraswing gate motors

    2. Apply the battery power. The operators will automatically turn until the closed limit
    is struck.

    Diagram for limit settings on dace duraswing
    3. Before tightening the crank arms ensure that the gates are set up correctly using the diagrams on pages 11 –15. The gates must now be placed in the closed position and
    the crank arms can now be tightened. (23mm spanner.)

    Diagram for limit settings on dace duraswing
    4. Loosen the limit rotor . The rotor is a black plastic cam shaped rotor. The rotor
    can be removed completely to assist with the set-up

    Diagram for limit settings on dace duraswing
    5. Press the test button on the PC Board. The gates will now start opening.

    Diagram for limit settings on dace duraswing
    6. When gate reaches the required open position, press the limit switch.
    This is made easier using a small flat screwdriver. The motor will stop.
    The limit switch can be released when the operators have stopped running.

    Diagram for limit settings on dace duraswing
    7. Lift and turn the rotor until it presses on the limit switch.

    8. Tighten the rotor . Do not over tighten. The limit switch

  • How Do I Wire An External Receiver To The Dace Dura Swing
    Gensix Technical26-04-2021

    When connecting any auxiliary equipment to the PC Board ensure that all power is removed
    from the PC Board.

    A DuraTronic external receiver can be connected to the PC Board. This will be necessary if there are more than 15 remotes to be used or if the range of the on-board receiver is not sufficient.The DuraTronic external receiver can hold 128 remotes. The DuraTronic receiver should be mounted outside the operator housing for increased range.

    Connection Diagram for Ex
    Block Diagram for connecting External Receiver to the Dura Swing gate Motor

  • How Do I Connect a Keyswitch or Receiver to the Dura Swing Gate Motor For Pedestrian Operation.
    Gensix Technical26-04-2021

    When connecting any auxiliary equipment to the PC Board ensure that all power is removed
    from the PC Board.

    A DuraTronic external receiver can be connected to the PC Board.

    Connection Diagram for Ex
    Block Diagram for connecting External Receiver to the Dura Swing gate Motor

    PEDESTRIAN OPERATION: A separate receiver, keyswitch or keypad must be connected to operate
    the gate in the pedestrian mode. The connection is done in the same manner as the diagram above with the exception of the TRIG connection. Instead of TRIG to N/O it must be PED on the main PC Board to N/O.

    In pedestrian mode the gate will open partially and then close automatically after 6 seconds

  • How Do I Connect A Set Of Safety Beams To The Dura Swing Gate Motor
    Gensix Technical26-04-2021

    Wiring Diagram - Connect Safety Beams to Dura Swing Motor

    Note: although the installation of infrared safety beams does reduce the risk of the gate
    striking an object while closing it does not guarantee against it.

WP Twitter Auto Publish Powered By : XYZScripts.com
Verified by MonsterInsights